How to conduct a PPE risk assessment for blasting operations?

Selecting the right PPE for blasting is not a product decision: it is a risk assessment process. The equipment you specify must be matched to the actual hazards present in your specific operations. Get this step right, and your PPE specification practically writes itself. Skip it, and you risk under-protecting workers or over-specifying equipment in ways that create compliance gaps.
This practical guide walks through a structured PPE risk assessment process for abrasive blasting operations.
Step 1: Identify the hazards specific to your operations
Blasting environments are not all the same. The hazards present depend on several variables:
Substrate material
What surface is being blasted? Concrete, brick, and stone substrates release crystalline silica. Steel surfaces generate metallic dust. Painted surfaces may release lead or chromate compounds in older structures. Each substrate type determines the respiratory risk profile.
Abrasive media
What media is being used? Natural silica sand is now banned in many countries due to silicosis risk. Steel shot, steel grit, garnet, and aluminium oxide each have different dust generation profiles and associated risks.
Environment
Is the work conducted in an open outdoor environment, a partially enclosed space, or a fully enclosed environment like a tank or vessel? Enclosed spaces dramatically increase dust and gas concentrations and create additional hazards including oxygen depletion and toxic gas accumulation.
Duration and intensity
How many hours per shift is the operator actively blasting? Cumulative exposure determines the dose: an operator working 6 hours per day has a very different risk profile from one working 2 hours.
Temperature and climate
What are the ambient temperature conditions? Operators working in hot climates or in summer months face heat stress risks that must be controlled through equipment selection and work planning.
Step 2: Evaluate the risk level for each hazard
For each identified hazard, assess:
- Severity: What is the worst-case outcome if the hazard is not controlled? (e.g., fatal for silicosis and CO poisoning; serious injury for impact and noise)
- Likelihood: How probable is exposure given the working conditions?
- Current controls: What controls are already in place, and are they adequate?
This evaluation determines which hazards require the most stringent controls and helps prioritise equipment selection.
Step 3: Define PPE requirements by hazard
Map each identified hazard to a PPE requirement:
- Crystalline silica / fine dust → Supplied-air respirator (SAR) certified to EN14594 Class 4B minimum
- Toxic gases in air supply (CO, H₂S) → Gas monitoring at the air source (GX4® Gas Monitor detects CO, O₂, H₂S)
- Abrasive rebound → Full blast suit + certified visor (EN16321 Class 1D minimum)
- Head impact → EN397-certified helmet shell integrated with respirator
- Noise > 85 dB(A) → Integrated or compatible hearing protection
- Heat stress → Climate control device (C40™) for warm environments
- Slip hazard → EN ISO 20345 safety footwear with slip-resistant soles
- Hand lacerations → EN388-rated cut-resistant gloves
Step 4: Select certified equipment matched to requirements
Once PPE requirements are defined, select equipment that meets the relevant certifications. Key questions:
- Is the respiratory equipment certified to the correct class for the identified risk level?
- Is the complete system compatible: helmet, airline, filter, and gas monitor working together?
- Is the equipment suitable for the duration of use (comfort and ergonomics for all-day wear)?
- Is the equipment available in appropriate sizes for all workers?
Step 5: Verify compatibility of the complete PPE system
Individual PPE items must be compatible with each other. A common failure mode is selecting a helmet certified to EN14594 but pairing it with an airline that is not certified to the same standard, or using a filter that does not remove the relevant contaminants.
The Radex® Airline Filter, for example, removes moisture and particles down to 0.5 microns and should be paired with a certified SAR helmet. The GX4® Gas Monitor provides continuous monitoring at the air source and should be part of any supplied-air system where compressor air quality cannot be guaranteed.
Step 6: Document the assessment
A risk assessment is only useful if it is documented. Your PPE risk assessment record should include:
- The hazards identified and the basis for that identification
- The risk evaluation for each hazard
- The PPE controls specified and the standards they must meet
- The specific equipment selected and its certification references
- The date of assessment and scheduled review date
- Sign-off by a competent person (HSE manager or safety officer)
Step 7: Review regularly and after incidents
A PPE risk assessment is not a one-time document. It should be reviewed whenever there is a significant change in working conditions, substrate materials, or abrasive media, and immediately following any incident or near-miss.
Key takeaways
- PPE selection must be driven by a formal hazard assessment, not by cost or habit.
- The substrate, media, environment, duration, and climate are the key variables to assess.
- The complete PPE system must be certified and compatible: not just individual items.
- Documentation is both a legal requirement and a practical management tool.
- Review the assessment regularly; working conditions change.






